Submit a ticketCall us

Announcing NPM 12.2
With NPM 12.2 you can monitor your Cisco ASA firewalls, to monitor VPN tunnels for basic visibility and troubleshooting tunnels. NPM 12.2 also uses the SolarWinds Orion Installer so you can easily install and upgrade one or more Orion Platform products simultaneously.
See new features and improvements.

Home > Success Center > Storage Manager (STM) > SRM Profiler Administrator Guide > Appendices > Configure storage arrays > HP Lefthand

HP Lefthand

Updated: June 16, 2017

This information is provided 'as-is' as a reference for our customers. SolarWinds provides no guarantees as to the accuracy of this information as the software is built and distributed by 3rd party vendors who may make changes at any time. SolarWinds does not provide official support for problems related to vendor's SMI-S Providers, but customers can seek support via Thwack. Our product team and other knowledgeable customers regularly use these forums and may be able to assist you.

This section details enabling SNMP polling on the management nodes from the poller agent assigned to poll LeftHand devices. Once enabled, the SNMP data will appear within the LeftHand device console screen.

Centralized Management Console (CMC) structure

To begin you need to drill down in the cluster to locate a management node.

File:Success_Center/Reusable_content_-_InfoDev/SRM_Profiler/Enabling_SNMP/030000B7_255x283.png

Find a management node

To find a management node for a specific cluster.

  1. Click on the node, and then check the Status on the Details tab.
  2. If the status reads Manager Normal then it is a management node.

    File:Success_Center/Reusable_content_-_InfoDev/SRM_Profiler/Enabling_SNMP/030000B8_297x168.png

Enabling SNMP:

SNMP must be enabled to allow the respective SRM Profiler proxy agent to access the information. After adding permissions to one node you will then need to copy these permissions to the rest of the nodes.

To check if SNMP is enabled:

  1. Click the SNMP icon below one of the nodes.
  2. Check that Agent Status is enabled on the SNMP General tab.
  3. If SNMP is not enabled, use Edit SNMP Settings to enable it.

    File:Success_Center/Reusable_content_-_InfoDev/SRM_Profiler/Enabling_SNMP/030000B9_157x93.png

To find the Community String:

  1. Click the SNMP icon below one of the nodes.
  2. Check the Community String. If it is different than public make sure this is reflected within SRM Profiler.
  3. If the Community String needs to be changed see Edit SNMP Settings below for steps.

Community Strings are CASE sensitive and need to reflect their case sensitivity in SRM Profiler as well.

File:Success_Center/Reusable_content_-_InfoDev/SRM_Profiler/Enabling_SNMP/030000BA.png

To check if SRM Profiler proxy agent is in Access Control list:

Check the Access Control list and see if the SRM Profiler proxy agent's IP address is in the list. If not, it will need to be added. To do so, see Edit SNMP Settings below.

File:Success_Center/Reusable_content_-_InfoDev/SRM_Profiler/Enabling_SNMP/030000BB_279x145.png

Edit SNMP Settings:

Near the bottom of the CMC screen there is a SNMP General Tasks drop down. From here click Edit SNMP Settings.

File:Success_Center/Reusable_content_-_InfoDev/SRM_Profiler/Enabling_SNMP/030000BC_148x98.png

From this page you can set SNMP to enabled, change the Community String and add the SRM Profiler proxy agent to the Access Control list.

File:Success_Center/Reusable_content_-_InfoDev/SRM_Profiler/Enabling_SNMP/030000BD_304x253.png

Add the SRM Profiler proxy agent IP to Access Control list:

From the Edit SNMP Settings page, click Add.

File:Success_Center/Reusable_content_-_InfoDev/SRM_Profiler/Enabling_SNMP/030000BE_337x113.png

This will bring you to the Add SNMP Client page. From here, click the By Address radio button and add the IP address of the SRM Profiler proxy agent, and then click OK.

File:Success_Center/Reusable_content_-_InfoDev/SRM_Profiler/Enabling_SNMP/030000BF_201x134.png

The SRM Profiler proxy agent IP should now be in the Access Control list. The last step is to copy these SNMP settings to the rest of the nodes within the cluster. To do this return back to the node page.

From the Node page you can click on the Storage Node Tasks drop down at the bottom of the page and select Copy Configuration.

File:Success_Center/Reusable_content_-_InfoDev/SRM_Profiler/Enabling_SNMP/030000C0_166x221.png

This will bring up the Copy Configuration box, and from here you can select the SNMP Settings and select the nodes you want to copy the configuration to by checking the checkbox for SNMP Settings (General, Traps) and by selecting the nodes you wish to copy the selected configuration to.

File:Success_Center/Reusable_content_-_InfoDev/SRM_Profiler/Enabling_SNMP/030000C1_285x182.png

After you click copy the configuration is copied to all the nodes selected. You should now see the SRM Profiler proxy agent IP in each node's Access Control list.

  • Management Group
  • Servers
  • Cluster
  • Node
  • SNMP Settings

Disclaimer: Please note, any content posted herein is provided as a suggestion or recommendation to you for your internal use. This is not part of the SolarWinds software or documentation that you purchased from SolarWinds, and the information set forth herein may come from third parties. Your organization should internally review and assess to what extent, if any, such custom scripts or recommendations will be incorporated into your environment.  You elect to use third party content at your own risk, and you will be solely responsible for the incorporation of the same, if any.

Screenshots property of © 2016 HPE

 
Last modified
10:47, 5 Jul 2017

Tags

Classifications

(not set)