Submit a ticketCall us

Systems Monitoring for Dummies
Our new eBook will teach you the fundamentals and help you create monitors and alerts that are effective, meaningful, and actionable. Monitoring is more than a checkbox on your to-do list. This free eBook will give you practical advice to help you succeed in all aspects of monitoring – discovery, alerting, remediation, and troubleshooting. Don’t miss out on this indispensable resource for newbies, experienced IT pros, and everyone in between. Register Now.

Home > Success Center > Network Performance Monitor (NPM) > NPM 12.2 Administrator Guide > Monitor ASA firewalls > Set up monitoring Cisco ASA firewalls

Set up monitoring Cisco ASA firewalls

Updated: September 13, 2017

Data for monitoring Cisco® ASA firewalls is polled by a combination of SNMP and CLI polling. To get accurate ASA-specific information, add the firewall device to NPM as a node, and provide CLI credentials.

What does CLI polling provide?

Enable CLI polling to receive additional ASA-specific details, and to display accurate information for your Cisco ASA devices.

For example, when polling Site-to-Site VPN tunnels, CLI polling helps filter data polled through SNMP, and display only relevant results. Without CLI polling, you might see failed access attempts from outside as failed tunnels.

Information polled by CLI

  • Security level and standby IP address for interfaces
  • Number of failed connections per minute on the ASA
  • High availability details:
    • Configuration sync state
    • Connection sync state
    • Standby state
    • High availability mode
    • Last failover date and time
    • System HA type and system HA role
    • Peer interfaces
  • Firewall mode, serial number, and contexts on the ASA device
  • All configured Site-to-Site tunnels on the ASA, including inactive tunnels
  • For Site-to-Site tunnels, local IP address, local host name, remote IP address, and remote host name

Requirements

Requirement Details
Cisco ASA version Cisco ASA 8.2 and later
ASA user account Credentials for logging into the ASA device
Enable password Credentials for polling CLI details. Without this password, you can access the ASA, but cannot poll it.
SSH port

By default, port 22.

Open an SSH port for accessing and polling ASA devices through SSH.

Add ASA firewalls using CLI credentials

You need Node Management Rights. See Define what users can access and do.

  1. Click Settings > Manage Nodes, and then click Add Node.
  2. Enter the IP address for the device.
  3. Select Most Devices: SNMP and ICMP as the polling method, and enter SNMP credentials.
  4. Enable CLI monitoring:
    1. Scroll down to Additional Monitoring Options.
    2. Select Advanced Cisco ASA monitoring, enter the credentials, and click Test.
       

      Enter a user name and password for logging into the ASA device.

      Enter the security password for CLI polling. Without the Enable Password, CLI polling does not work.

       

      File:Success_Center/Network_Performance_Monitor_(NPM)/NPM_Administrator_Guide/ASAs/ASA_reuse/0010-Monitor_ASA_firewalls/0010-Set_up_monitoring_Cisco_ASA_firewalls/advanced_asa_monitoring.png

  5. To use a specific device template, select it. Device templates are sets of commands you can execute on a device. See NCM Getting Started Guide for more information.
  6. Complete the Add Node wizard.

You can now view the polled ASA firewall information in NPM.

Enable CLI polling on monitored devices

To poll firewall-specific data on ASA devices already monitored in SolarWinds NPM, enable CLI polling for ASAs.

  1. On the node details view, click Edit Node in the Management resource.
  2. Scroll down to Additional Monitoring settings, select Advanced Cisco ASA monitoring, and enter the credentials.
  3. Click Submit.

You can now poll firewall-specific information, such as platform, interface and tunnel details. Pollers for ASA Network Insight are enabled.

Troubleshoot CLI polling

If CLI polling has issues, verify the following:

  • You have enabled CLI polling on the ASA device.
  • You are using the correct user credentials to log in to the ASA device.
  • You are using the correct password for CLI access.
  • You have enabled Cisco ASA NetInsight pollers:
    1. On the node details view, click List Resources in the Management resource.
    2. Expand Cisco ASA NetInsight, and select to enable the pollers.

      File:Success_Center/Network_Performance_Monitor_(NPM)/NPM_Administrator_Guide/ASAs/ASA_reuse/0010-Monitor_ASA_firewalls/0010-Set_up_monitoring_Cisco_ASA_firewalls/asa-listresources.png

  • Enable the CLI session trace to extend logging:
    1. Click Settings > All Settings > CLI Settings in the Product Specific grouping.
    2. Click Enable Session Tracing, and click Submit.

    Review the session trace files located at:

    %ALLUSERSPROFILE%\Application Data\SolarWinds\Logs\Orion\CLI\Session-Trace

Last modified

Tags

Classifications

Public